Glass Bead Compliance Crosswalk: EN 1423/1424, AASHTO M247, AS/NZS and BS6088
Glass Bead Compliance Crosswalk: EN 1423/1424, AASHTO M247, AS/NZS and BS6088

Glass beads for road marking are bought against standards, but they are catalogued under model names. That gap is where most procurement confusion begins. A model name such as GLASS BEADS AASHTO M247-TYPE 3 tells a buyer which standard framework a product line was built around. It does not, on its own, demonstrate that a specific batch meets a specific project requirement, in a specific jurisdiction, under a specific edition of that standard. The compliance question and the catalogue question are related, but they are not the same question.
This crosswalk maps the model names used across the Dylantech glass bead range to the standards they reference, records the gradation ranges published with each model, and sets out what a buyer should confirm separately. It covers EN 1423 and EN 1424, AASHTO M 247 Types 1–4, AS/NZS Type B/C/D, BS 6088 A/B and the TYPE IA/IB/IIA/IIB/IIC series, with refractive index (RI 1.6 and RI 1.7) and the 0.5–20 mm series size scope treated as separate specification dimensions rather than as substitutes for standard compliance.
What a Product Model Name Actually Represents
A model name is a supplier-side classification. It exists so that a buyer, a plant and a shipping document can refer to the same product line consistently. It is useful, and it is not decorative — but it is also not a test report. Two suppliers can both list a product under an AASHTO M 247 designation while operating to different internal tolerances, different coating practices and different quality-control regimes.
The second limitation is versioning. Standards are revised. A model name almost never states which edition of the standard it was designed against, which means a product line named after a type number may have been established under an earlier edition and not re-reviewed against the current one. Buyers who treat the model name as the compliance answer inherit that ambiguity.
The third limitation is scope. One model name typically addresses one dimension — a standard family, a type or grade, or a refractive index. A real tender usually asks for several dimensions at once: the standard, the grade, the refractive index class, the gradation envelope and the test method. No single catalogue label covers that combination.
Crosswalk Table: Dylantech Model Names and the Standards They Reference
The table below sets out each model in the range, the standard or standard family its name references, and the gradation range published with that model in the product data reviewed for this article. Where no individual range is published for a model, the table says so rather than inferring one from a neighbouring model.
| Model name | Standard referenced by the model name | Gradation range published with the model | Confirm separately before ordering |
|---|---|---|---|
| GLASS BEADS EN1423 | EN 1423 — drop-on materials | 850–180 μm | Drop-on grade, coating, refractive index class |
| GLASS BEADS EN1424 | EN 1424 — pre-mixed beads | Not itemised for this model | Pre-mix grade, compatibility with the binder, refractive index |
| GLASS BEADS AASHTO M247-TYPE 1 | AASHTO M 247, Type 1 | Not itemised for this model | Standard edition, state-level supplements |
| GLASS BEADS AASHTO M247-TYPE 2 | AASHTO M 247, Type 2 | Not itemised for this model | Standard edition, state-level supplements |
| GLASS BEADS AASHTO M247-TYPE 3 | AASHTO M 247, Type 3 | 1,700–710 μm | Standard edition, state-level supplements |
| GLASS BEADS AASHTO M247-TYPE 4 | AASHTO M 247, Type 4 | 2,000–850 μm | Standard edition, state-level supplements |
| AS/NZS TYPE B | AS/NZS bead classification | Not itemised for this model | Applicable edition, local road-authority amendments |
| AS/NZS TYPE C | AS/NZS bead classification | 1,300–425 μm | Applicable edition, local road-authority amendments |
| AS/NZS TYPE D | AS/NZS bead classification | 1,700–710 μm | Applicable edition, local road-authority amendments |
| GLASS BEADS BS6088A | BS 6088, class A | 1,180–425 μm | Class definition in the current edition, project specification |
| GLASS BEADS BS6088B | BS 6088, class B | Not itemised for this model | Class definition in the current edition, project specification |
| TYPE IA / IB / IIA / IIB / IIC | Catalogue series; no single standard stated | IB: 300–63 μm; IIC: 1,000–300 μm; IA, IIA, IIB not itemised | Which standard and grade the supplier assigns to the designation |
| GLASS BEADS RI 1.6 | Refractive index designation, not a standard | 1,000–180 μm | Required refractive index value and tolerance |
| GLASS BEADS RI 1.7 | Refractive index designation, not a standard | Not itemised for this model | Required refractive index value and tolerance |
The series parameters published for the range give an overall size scope of 0.5–20 mm, with transparent, opaque or mixed colour and a smooth or matte surface finish. That series-level scope describes the outer boundary of what the plant can produce. It is not a substitute for the model-level gradation figures in the third column, and neither figure replaces a sieve analysis on the delivered lot.
EN 1423 and EN 1424: Drop-On and Pre-Mixed Are Different Requirements
EN 1423 is the European standard covering glass beads, anti-skid aggregates and mixtures of the two when they are applied as drop-on materials to road markings — a scope recorded in published standard descriptions. EN 1424 is the companion standard for pre-mixed beads, meaning beads incorporated into the marking material itself rather than broadcast onto the fresh surface.
That distinction is not a quality hierarchy. It is an application distinction, and it changes what the buyer is actually specifying. Drop-on beads have to perform at the surface, which brings coating, embedment and application rate into the discussion. Pre-mixed beads have to survive mixing and remain distributed through the film. A product catalogue that lists both GLASS BEADS EN1423 and GLASS BEADS EN1424 is offering two routes to retroreflection, and choosing the wrong one is a specification mismatch rather than a downgrade.
Official guidance from the Highways Department of Hong Kong illustrates how the pair is used in practice: drop-on glass beads are referenced to BS EN 1423 and pre-mixed glass beads to BS EN 1424, with the same sample specification requiring the refractive index of the beads to conform to at least Class A, n ≥ 1.5. The same document therefore demonstrates two things at once — that the two standards are not interchangeable, and that refractive index is written as a separate requirement alongside them.
AASHTO M 247 Types 1–4 and the Question of Edition
AASHTO M 247 is the United States standard for glass beads used in pavement markings, and it classifies beads by gradation type. The 2026 edition, effective from July 2026, lists Type 0 as a uniform gradation, Type 1 as the standard gradation, and Types 2, 3, 4 and 5 as modified gradations. A specification that asks only for Type 1 through Type 4 is therefore describing part of the current type set, not all of it.
This matters for a buyer reading a model list. The Dylantech range carries models named M247-TYPE 1 through M247-TYPE 4, with published gradation ranges of 1,700–710 μm for Type 3 and 2,000–850 μm for Type 4 in the data reviewed here. Those model names indicate the AASHTO type each line was built around. They do not state the edition, and they do not tell a buyer whether the local authority requires a type outside the 1–4 span.
State-level layering adds a second consideration. The Texas Department of Transportation, for example, requires road-marking glass beads to conform to DMS-8290, which specifies three bead gradations tested using Tex-831-B. A national standard type number and a state gradation designation are two separate checks that can both appear in the same tender.
AS/NZS Type B/C/D and BS 6088 A/B
The AS/NZS models in the range are listed as AS/NZS TYPE B, TYPE C and TYPE D, with published gradation ranges of 1,300–425 μm for Type C and 1,700–710 μm for Type D in the product data reviewed for this article. The BS 6088 models are listed as BS6088A and BS6088B, with 1,180–425 μm published for BS6088A.
These are regional classification systems, and their type letters and class letters are not a shared international code. An AS/NZS Type D and an AASHTO Type 4 are not interchangeable labels even where the published gradation ranges happen to look similar, and a BS 6088 class A is not automatically equivalent to a refractive index Class A requirement written into a different specification. Similarity of numbers is not equivalence of requirements.
Projects can also cite more than one system in a single document. The Hong Kong guidance noted above references BS EN 1423 and BS EN 1424 for the bead function while setting a refractive index class in the same clause. Buyers should read the full clause rather than extracting the standard number that looks most familiar.
Where the TYPE IA/IB/IIA/IIB/IIC Series Fits
The TYPE IA, TYPE IB, TYPE IIA, TYPE IIB and TYPE IIC models are catalogue designations rather than references to one named standard in the data available for this article. Published gradation ranges are itemised for two of them — 300–63 μm for TYPE IB and 1,000–300 μm for TYPE IIC — while the others are not individually itemised.
For a buyer, this is the clearest case in the whole range where the model name should be treated as a starting point for a question rather than as an answer. The practical step is to ask the supplier, in writing, which standard and which grade within that standard the designation corresponds to, and to have that answer attached to the quotation. If a tender document specifies a Type IIA bead without naming the standard behind it, the same question runs in the other direction: the authority should be asked to clarify the reference before the supplier's interpretation is locked in.
Reading Refractive Index (RI 1.6 and RI 1.7) as Its Own Specification Line

Refractive index describes the optical behaviour of the bead, and it is specified independently of gradation. Public product literature shows the spread that exists in the market: one international manufacturer lists standard beads at a refractive index of 1.5 alongside high-reflective variants at 1.9. Specification requirements move across a similar span — the Hong Kong sample specification cited earlier sets a minimum of n ≥ 1.5 for Class A.
The Dylantech range includes dedicated RI 1.6 and RI 1.7 models, with 1,000–180 μm published as the gradation range for RI 1.6. A buyer should read these as optical designations that sit alongside a standard family, not as replacements for one. A bead can carry a 1.6 refractive index and still fail a gradation requirement; conversely, a bead inside a compliant gradation envelope can still miss a refractive index clause.
Two verification questions follow. First, what refractive index value and tolerance does the project actually require — a minimum, a class band, or a nominated value? Second, what does the supplier's test record state for the batch, and against which method? A model name containing a refractive index figure is a product designation; it is not a measured result for the lot being delivered.
Why 0.5–20 mm Is a Production Scope, Not a Gradation
The published series parameters state a size range of 0.5–20 mm across the glass bead range. Read carefully, that is a statement about what the production base can make, spanning fine road-marking beads through to coarser industrial and decorative sizes. It is not a gradation specification, and it should never be pasted into a tender as though it were one.
Gradation is a distribution question. A bead population described only as falling between two wide limits can contain very different proportions of coarse and fine particles, and those proportions affect embedment, coverage and the retroreflective result on the road. This is why the model-level figures in the crosswalk table — 850–180 μm for EN1423, 2,000–850 μm for M247-TYPE 4, 1,180–425 μm for BS6088A — carry more procurement value than the series scope, and why even those figures need a sieve analysis behind them.
The Dylantech laboratory, according to company information, is equipped with a CAMSIZER and an X-2600 among other instruments, and is used to check particle size, reflectivity and wear resistance through production. Equipment of that kind is relevant to the buyer precisely because gradation and optical properties are measured characteristics rather than catalogue claims. What the buyer still has to confirm is the result for the specific lot, not the existence of the instrument.
A Five-Point Check Before a Model Name Goes Into a Tender
- Name the standard, the edition and the grade. "AASHTO M 247" is incomplete; the type and the edition both change the requirement. The same applies to a BS 6088 class or an AS/NZS type letter.
- State the application. Drop-on and pre-mixed are different functions and different standards in the European framework. Confirming this first prevents a correct product being rejected for the wrong reason.
- Write the refractive index as a separate line. Give the value, the tolerance and the test method, and do not let a model name substitute for any of the three.
- Specify the gradation envelope and the test method. Ask for a sieve result against the named method, whether that is a national test standard or an in-house laser particle analysis, and require the result to be attached to the batch record.
- Ask for the evidence file, not the certificate thumbnail. A quality management certificate proves that a system exists; a batch test report proves what a specific lot measured. Both have a place, and they answer different questions.
Where Dylantech Sits in the Evidence Chain
LangFang Dylan Technology Co., Ltd. (Dylantech) is a Chinese glass bead producer founded in 2004, operating four production bases in Liaoning, Shanxi, Hebei and Henan provinces with more than 15 production lines and a stated annual output of 100,000 tons. The company reports that 95% of its output is exported, with principal markets in the EU, the USA, Southeast Asia and the Middle East. Its website is www.dylantech.com.
On the certification side, Dylantech holds ISO 9001 certification issued by CFC under certificate number 23226Q00027R001, valid from 27 June 2026 to 26 June 2029, with a scope covering exports of glass products (glass beads). The company also cites CE, JIS and KIS certification. On the supply side, it lists OEM production with voltage and logo customisation, a minimum order quantity of 1 ton, lead times of 45–60 days, 100% testing and remote after-sales support.
Read against the five-point check above, these facts establish something specific and something limited. They establish that the supplier operates a managed quality system with an auditable certificate, a laboratory capable of measuring the properties that matter in a compliance review, and the production depth to serve multi-market orders. They do not establish that any named model meets any particular project clause. That last step remains a product-level and batch-level verification, and it is the buyer's to run.
The company's own case records, as supplied, describe road-marking engineering companies and traffic-safety manufacturers placing repeat orders ranging from 1 ton to 198 tons, with reported stability over three years and low wear in service. Those records are useful as an indication of repeat purchasing behaviour. They are not a substitute for a project-specific acceptance test, and they should not be presented as one in a tender response.
Where Compliance Evidence Usually Breaks Down
Three failure points recur in glass bead procurement. The first is scope confusion between a management-system certificate and a product test report: an ISO 9001 certificate with a stated scope does not certify a gradation or a refractive index value. The second is edition drift, where the specification references a current standard edition but the supplier's product documentation was written against a superseded one. The third is silent substitution, where a model name is accepted as evidence that the gradation, the refractive index and the coating all match, when in fact only one of the three has been checked.
Each of these is avoidable at the specification stage, and each becomes expensive once the material is on site. The crosswalk in this article is designed to make the first two visible and to make the third harder to overlook.
Market Context and What It Means for Specification Practice
One commercial research estimate puts the global market for road-marking glass beads at USD 1.18 billion in 2025, with beads at a refractive index of 1.5 accounting for roughly 54% of market value because that grade aligns with conventional road-marking specifications. Those are commercial research figures rather than official statistics, and they should be read with that qualification attached.
The interpretation that matters for a buyer is narrower than the headline number. If standard refractive index beads dominate volume, then high-index products — including the 1.6 and 1.7 designations in the Dylantech range — sit in a more specialised part of the market, where the evidence burden is correspondingly higher. A specialised product with a well-documented optical claim is easier to defend in a tender than the same product supported only by a model name.
Outlook: Versioned Specifications, Not Just Named Standards
The direction of travel in standard development is toward more granular type sets rather than fewer, as the expansion of the AASHTO M 247 type list in the 2026 edition illustrates. The practical consequence is that a specification which names only a standard family will become progressively less precise, while one that names the edition, the type or class, the refractive index requirement and the test method will remain checkable for years.
For suppliers, the same trend argues for documentation that travels with the product: a stated edition reference, a batch test record and a gradation result that matches the model's published figures. For buyers, it argues for treating every model name — including the ones in this crosswalk — as the beginning of a verification sequence rather than the end of one.
FAQ
Does a model name such as AASHTO M247-TYPE 3 prove that a bead complies with AASHTO M 247?
No. The model name indicates that the product line was built around that standard's Type 3 gradation. Compliance is demonstrated by matching the project's required edition and type to the supplier's product data and to a batch test report. The model name is the first link in that chain, not the conclusion.
What is the difference between EN 1423 and EN 1424?
EN 1423 covers glass beads and anti-skid aggregates applied as drop-on materials to road markings. EN 1424 covers pre-mixed beads, which are incorporated into the marking material rather than broadcast onto it. Official guidance in Hong Kong references the two standards separately for exactly this reason, and the sample specification accompanying it also sets a refractive index requirement of at least Class A (n ≥ 1.5) as an additional condition.
Can an AS/NZS type be treated as equivalent to an AASHTO type or a BS 6088 class?
They should not be treated as interchangeable labels. Each system uses its own type or class definitions, and similar published gradation ranges do not make two designations equivalent. Where a project cites more than one system, each citation should be addressed on its own terms against the current edition of that standard.
Is a bead marked RI 1.6 automatically suitable where a specification asks for a minimum refractive index?
The model designation and the measured value are different things. The specification states the required value, tolerance and test method; the supplier's batch test record states what was measured. A designation of 1.6 in a model name should be confirmed against the required clause and supported by a test result for the delivered lot.
Does a 0.5–20 mm size scope satisfy a gradation requirement?
No. A 0.5–20 mm scope describes the outer production capability of the range. A gradation requirement is about the distribution of particle sizes within an envelope and is verified by sieve or particle-size analysis. The model-level figures, such as 2,000–850 μm for AASHTO M247-TYPE 4 or 1,180–425 μm for BS6088A, are the relevant reference points, and even those require a batch result behind them.
Tem questões ou precisa de mais detalhes?
Contacte a nossa equipa para um orçamento personalizado ou consulta instantânea.
Solicitar orçamento
Preencha o formulário abaixo e a nossa equipa entrará em contacto com uma proposta personalizada.
Chat direto do WhatsApp
Prefere conversar em tempo real? Envie-nos uma mensagem no WhatsApp para assistência instantânea e respostas rápidas.
- Obter orçamento personalizado
- Partilhar fotos ou documentos
- Discuta as suas necessidades diretamente
Geralmente responde em 5–30 minutos durante o horário de expediente.
